 +86-571-88842852  
  oceanindustry@vip.163.com 
You are here: Home » News and Events » 35MnB Boron Steel Quenching & Tempering: Why Just A Few Grams of Boron Per Ton Enables 10.9 High-Strength Bolts

35MnB Boron Steel Quenching & Tempering: Why Just A Few Grams of Boron Per Ton Enables 10.9 High-Strength Bolts

Views: 0     Author: Site Editor     Publish Time: 2026-11-18      Origin: Site

35MnB may sound unremarkable to outsiders, yet seasoned heat treatment specialists recognize it as a highly efficient microalloyed steel. As a medium-carbon steel, it relies on a tiny boron addition to deliver outstanding performance for high-strength bolt applications.

Grade Overview

35MnB is a premium boron-containing structural steel specified under GB/T 3077. There is no direct equivalent grade in ASTM or JIS standards. American boron steels such as 15B35 and 50B44 follow a different carbon design route and cannot be treated as matching alternatives; 35MnB is a characteristic boron steel developed under Chinese national standards.

Three core chemical composition ranges should be noted:

  • Carbon: 0.32~0.39%

  • Manganese: 1.10~1.40%

  • Boron: 0.0005~0.0035%

Boron stands out despite its extremely low content. Only several grams to tens of grams of boron are added per ton of steel, yet this minor element generates dramatic property improvements.

Working Mechanism: How Trace Boron Works

Boron atoms are small in size. During austenitization before quenching, boron segregates and occupies grain boundaries. Grain boundaries are the preferred nucleation sites for soft phases including ferrite and pearlite. Once grain boundaries are pinned and blocked by boron atoms, soft phase formation is suppressed, and martensite can form readily upon quenching. This is the core mechanism for remarkable hardenability improvement.

Manganese itself also boosts hardenability. Manganese provides a baseline hardenability, while trace boron delivers a powerful supplementary effect. Combined, the hardenability of 35MnB can reach the level of expensive Ni-Cr alloy steels at a much lower material cost. It is widely regarded as a cost-effective high-strength steel grade.

Critical Limitations: Three Major Enemies of Boron

Boron delivers strong benefits but is highly sensitive to processing conditions. Three risk factors can render boron ineffective:

  1. Susceptible to Nitrogen Nitrogen readily reacts with boron to form boron nitride, which eliminates boron’s hardenability contribution. Titanium and aluminum are added during steelmaking to fix free nitrogen and protect active boron.

  2. Susceptible to Excessive Temperature Overhigh austenitizing temperature causes excessive boron segregation at grain boundaries and grain coarsening, which degrades performance. Quenching temperature must be tightly controlled instead of simply raised.

  3. Prone to Temper Embrittlement Both manganese and boron aggravate reversible temper embrittlement (second-kind temper embrittlement). The cooling procedure after tempering becomes a decisive control point.

Tempering Process Windows & Applications

表格

Tempering Type

Temperature

Holding & Cooling

Hardness

Typical Application

Low-temperature tempering

180~250℃

4 h

HRC ≥55

Track pads, block teeth, wear-resistant parts

Medium-temperature tempering

300~400℃

3 h, oil quenching after discharge

—

Avoid temper embrittlement zone

High-temperature tempering

500~550℃

2 h, air cooling

HRC 34~40

10.9 grade fasteners

Standard quenching condition: 840~860℃, 60 min holding, water or oil quenching. Higher hardness can be obtained by adjusting temperature up to 890~900℃. This is the upper limit. Further temperature rise or prolonged holding will trigger grain coarsening and boron failure, reducing hardenability instead.

Tempering Cooling: A Common Failure Source

Many quality defects of 35MnB components originate from improper cooling after tempering. For medium-temperature tempering at 300~400℃, oil cooling immediately after furnace discharge is required to rapidly cross the embrittlement temperature range.

High-temperature tempering at 500~550℃ falls right inside the sensitive interval of reversible temper embrittlement. Air cooling works for small-section bolts with moderate toughness requirements. For thick-section workpieces and parts with strict toughness requirements, accelerated cooling via oil or water is recommended to avoid embrittlement.

Slow cooling inside the furnace after high-temperature tempering will sharply reduce impact toughness and lead to brittle fracture, an issue especially prominent in Mn-B bearing steels.

Application Scope & Typical Pitfalls

✅ Suitable applications:

  • 10.9 grade high-strength bolts (high-temperature tempering at 500~550℃, HRC 34~40, tensile strength ≥1040 MPa)

  • Track components, tooth blocks (low-temperature tempering, HRC 55+, high wear resistance)

❌ Must avoid these improper operations:

  • Overheating above 900℃ with extended holding: boron segregation failure + grain coarsening, reduced hardenability

  • Missing Ti/Al nitrogen fixation during smelting: boron consumed by nitrogen, no hardenability gain

  • Slow cooling after medium or high-temperature tempering: severe temper embrittlement and deteriorated impact property

Core Takeaway

Trace boron improves hardenability by segregating at grain boundaries and suppressing soft phase nucleation. Manganese builds basic hardenability while boron amplifies the effect. Three rules for boron control: protect boron from nitrogen with Ti/Al, strictly limit austenitizing temperature, and adopt fast cooling after tempering to avoid temper embrittlement.

Category List

Make Business Easier

We offer not only products, but also our after-sales service.
View More >

Quick Links

Contact Us

​Tel:  +86-571-88842852
Fax: +86-571-88844378
Email: oceanindustry@vip.163.com
oceanindustry011@hzoic.com
Add: 4th Floor, Block 2, Qianjiang Century Industrial Park, 2327 Hongning Road,Ningwei Town,Hangzhou, China
Leave a Message
​Copyright © Hangzhou Ocean Industry co.,Ltd. All Rights Reserved. Site Map